Image to Layers — No Photoshop Skills NeededTry ImageLayered ↗

Robotics Lab

Explore eight 3D boards and wire circuits on a virtual workbench.

An online robotics lab for boards, wiring, and circuits

The Robotics Lab app brings board models and a virtual electronics workbench together. Rotate a board to find its connectors, inspect a specific part in the lesson, then move to the bench to see what happens when you connect a sensor or an output module. The circuit missions let you start with an LED and work up to projects with a display, a servo, or more than one board.

If you want to spend more time on the Uno, follow the small experiments in Learn Arduino. When you reach a project with a network connection, Protocol Explorer shows how messages move between devices and services.

To practise thinking about timing, listen to a short word in the Morse Code Translator and count the short and long signals. Then look at the LED mission’s sketch and find the delays that determine how long its output stays on or off.

How it works

How to use Robotics Lab

1

Pick a board and inspect its pins

Start with the Arduino Uno R3 if you are new to electronics. Switch to Top view and turn on Labels to locate the power header, ground pins, and digital pins. Open Lesson to see what each part does, then find one of those parts again with the labels off.

2

Open the workbench and connect a circuit

Choose Open on the workbench, then open Missions and select Hello, LED. The Steps tab shows the two connections. Click the first pin and then its matching pin to place a wire. Use Show me if you have trouble finding a pin, or Wire it for me to inspect the completed circuit.

3

Run the circuit and observe the result

Press Run after completing the connections and watch the LED blink. Open Code to match the visible behavior to the example sketch. For a mission with an adjustable input, move the control and watch the output change. If the circuit does something unexpected, compare your wiring with Steps before trying again.

Features

Robotics Lab features

Eight interactive 3D development boards

Inspect the Arduino Uno R3, Nano, and Mega 2560 R3 alongside the ESP32 DevKit V1, NodeMCU ESP8266, Raspberry Pi Pico, STM32 Blue Pill, and Raspberry Pi 4 Model B. Switch between camera angles to see connectors and headers that are hard to identify from a single photo. The Compare section lists board specifications side by side.

Guided missions and a free-build workbench

Add boards, sensors, displays, and motor modules to the virtual bench. Guided missions show which pins to join and explain what to expect when the simulation runs. Free build opens a blank bench where you can assemble your own setup. Workbench tabs give you access to the wiring steps, example code, and serial output where applicable.

Part-identification quizzes and board assembly

Find the part asks you to identify a named component directly on the board model. Use a hint when you get stuck, then replay the quiz and try the same part from another angle. Assemble it gives you a bare board and a tray of parts so you can practise matching chips, connectors, and headers to their footprints.

Use cases

Who uses Robotics Lab?

Learn robotics before buying a kit

Start with one board and one visible output. Once you can explain why an LED needs both a signal and a path to ground, try a push-button or potentiometer mission. You can get familiar with common part names and see how the input, sketch, and output fit together before choosing physical parts.

Teach a short electronics lesson

Project the workbench and ask students to predict what they will see before pressing Run. Give them the pin names and have them find the pins on the model. Follow up with the part-identification quiz, then ask each student to explain what the board reads and what it controls in the circuit.

Compare boards for a project

Use Compare to narrow the options by logic voltage, available pins, and connectivity. Open the two board models to see where their connectors sit. For a sensor project, identify the pins needed for data and power before making a parts list, then check the physical components against their manufacturer documentation.

A closer look

Example 1 · Blink an LED with an Arduino Uno

Select Hello, LED in Missions. Connect the Uno’s D13 to the LED module’s signal pin and connect ground to the module’s ground pin. Run the mission and count how long the LED stays on and off. In the Code tab, find the two delays that control the blink and match each delay to the state you just observed.

Example 2 · Control a servo with a knob

Open Servo follows the knob and follow the Steps tab to wire the potentiometer and servo. Run the circuit, then try the knob at each end of its range and near the middle. Watch where the servo arm stops at each position. This exercise pairs a changing input with a physical output you can see on the workbench.

Example 3 · Display temperature and humidity on a Pico

Choose Pico weather screen to connect a temperature and humidity sensor and an OLED display to a Raspberry Pi Pico. Before running the mission, trace which wires carry power and which carry signals. Afterwards, use the two readings on the display to explain what information comes from the sensor and where the Pico sends it.

Common questions

Robotics Lab FAQ

What is the Robotics Lab app?

Robotics Lab is a browser-based learning app for electronics and robotics. It combines interactive 3D board models with lessons, quizzes, and a virtual workbench. You can learn where a pin sits on a board, use it in a simulated circuit, and compare the board with other options in the same session.

Is Robotics Lab free, and do I need hardware?

Yes, the embedded Robotics Lab app is free to open and use. The board models, missions, and workbench run in the browser without a physical board, USB cable, or electronics kit. Start with the virtual Uno and LED, then use a physical kit when you want to practise wiring actual components.

Which board and mission should beginners choose?

Start with Arduino Uno R3 and the Hello, LED mission. The circuit has two connections, so you can focus on identifying the digital output and ground pins. After you can explain the blink using the example sketch, try Push to light to see how a button changes what the board does.

Can I build my own circuit in Robotics Lab?

Yes. Open Missions and select Free build to start with an empty workbench. Choose from the available boards and modules and make connections between their pins. Practise with the supported components and guided examples, and use your board’s documentation and development tools when moving to physical hardware.

Can I use the Robotics Lab app on a phone?

You can open the lab in a mobile browser with JavaScript and WebGL enabled. The embedded app adjusts to the available screen space. Use Open app to give it a full browser tab if the workbench feels cramped. A larger screen makes it easier to distinguish adjacent pins while wiring.